(754) 714-8445

Broward County

Flat Roofing in Pembroke Pines, FL

Flat and low-slope roof work in Pembroke Pines starts with drainage, substrate, connected roof sections, access, and a clearly defined property responsibility.

  • Licensed & insured
  • Florida License CCC1332459
  • Free, no-obligation estimates
  • Serving South Florida
Call (754) 714-8445
M&M Roofing’s Fort Lauderdale Google reviews: 5.0 rating, five stars
M&M Roofing BBB rating: A+

Free Roofing Estimate

Get a Free Flat Roofing Estimate in Pembroke Pines

The service and location are already selected for you.

Add project details (optional)

No obligation. We use your details to respond to this request.

Prefer to speak now? (754) 714-8445

Plan the connected roof areas

Price the patio, garage or addition as a complete roof

Replacing a smaller flat section still requires a complete assembly and a sound connection to the roof above it. Compare what each proposal removes, retains and restores before choosing the lowest total.

Completed TAMKO Titan XT Shadow Grey shingle roof beside the finished flat roof in Fort Lauderdale.

Real Fort Lauderdale Project

Shingle and Flat Roof Replacement

See how one home received TAMKO Titan XT shingles over Polystick IR-Xe on the sloped sections and a hot-mopped GAFGLAS built-up system on the flat roof.

View the Fort Lauderdale case study

This Fort Lauderdale home is a nearby example of separate shingle and built-up flat-roof assemblies on one property. The approved system for a Pembroke Pines project depends on its own deck, slope, condition and details.

Inside the Fort Lauderdale installation

These photos document steps from this Fort Lauderdale job. The work sequence and assembly for another roof depend on its condition and project requirements.

Roof deck opened for replacement of deteriorated plywood and damaged perimeter wood in Fort Lauderdale.
Fort Lauderdale: Damaged decking and perimeter wood were removed and rebuilt before the new roofing systems were installed.
Roofing crew installing GAFGLAS roofing ply over the secured flat-roof base sheet in Fort Lauderdale.
Fort Lauderdale: The secured GAFGLAS #75 Base Sheet was followed by the hot-mopped reinforcing ply.

Three scope questions for a connected flat roof

Which roof areas are included?

Have the estimate identify the patio, garage or addition and its boundary with retained roofing. Include the work needed to open and restore that connection, even when the main roof stays.

What sits beneath the new surface?

Ask for removal, deck repairs, base and membrane layers, attachment and surfacing to be named. Any insulation or drainage correction should be a stated part of the scope.

What work belongs to another trade?

Identify equipment, lines, gutters, wall finishes and electrical or mechanical work affected by the roof. Agree on who completes each item and how it fits the roofing schedule.

Bring these details to the assessment

  • Show where leaks appear indoors and whether they occur during wind-driven rain or after water stands.
  • Identify the part of the roof you want replaced and any shared or association-managed areas.
  • Gather previous repair invoices, roof information and equipment changes when available.
  • Ask how additional deck damage will be photographed, priced and approved after opening the roof.

Define the roof area, drainage path, and responsibility first

Low-slope roofing in Pembroke Pines may cover a patio, garage, addition, townhouse section, or another area connected to a steeper tile or shingle roof. Before a membrane is selected, the scope should establish which roof areas belong to the project, where water exits, whether walls or neighboring roof sections share the assembly, and who controls any common or association-managed components. Those boundaries are especially important on attached properties.

M&M Roofing evaluates ponding clues, drains and scuppers, gutters, parapets, penetrations, equipment, substrate condition, insulation where present, and the transition beneath the upper roof. The selected approved assembly should identify preparation, base and membrane components, flashing, edge details, surfacing, attachment, and tie-ins. A coating or surface repair should not be presented as a substitute for correcting an unsuitable substrate or failed transition.

If the tile or shingle roof above the flat section also needs attention, our Pembroke Pines roofing page covers replacement, repair and City, HOA and HVHZ permit planning for the whole home.

Drainage before membrane choice

Map high and low areas, outlets, overflow paths, recurring ponding, and water arriving from upper roofs before selecting the assembly.

Project boundaries

Clarify included roof sections, shared walls, attached units, association responsibilities, and retained adjacent roofing in writing.

Connected-roof sequencing

The upper steep-slope underlayment and flashing should direct water onto the low-slope assembly without an exposed reverse lap.

Property Details We Consider in Pembroke Pines

Patios and Florida rooms

Lightweight additions and enclosed outdoor areas may have different decks, slopes, edges, and transitions than the main home.

Parapets and shared walls

Base flashing, counterflashing, coping, stucco termination, and neighboring construction can control where water enters.

Rooftop equipment

Curbs, stands, lines, drains, and service clearances may require coordination with mechanical, electrical, or other qualified trades.

Planning Flat Roofing in Pembroke Pines

  1. Confirm ownership and scope

    Identify the roof areas and components controlled by the homeowner, association, or neighboring property.

  2. Map water movement

    Inspect slope, outlets, ponding clues, upper-roof discharge, walls, equipment, and penetrations.

  3. Select the approved assembly

    Document substrate preparation, insulation or cover board where specified, membranes, flashing, edges, and attachment.

  4. Coordinate approvals and trades

    Align property approvals, permit documents, equipment work, inspections, access, and closeout responsibilities.

Flat Roofing FAQs for Pembroke Pines

Can only the patio or garage flat roof be replaced?

Often it can, but the retained roof and shared transition must be serviceable and clearly detailed. The proposal should identify the exact termination and how water moves between the assemblies.

Will a new membrane automatically eliminate ponding?

Not necessarily. Ponding can result from deck shape, settlement, insulation, drains, scuppers, gutters, or upper-roof discharge. Corrective work must be included specifically in the scope.

Who handles rooftop air-conditioning components?

Roofing can include specified flashing and curb work, but relocation, replacement, electrical, refrigerant, or mechanical work may require separate licensed trades and permits. Responsibilities should be established before installation.

What should a flat-roof replacement proposal identify?

It should identify included roof areas, removal and retained materials, the proposed roof assembly, deck allowances, flashing, edges, drainage work, transitions and exclusions. Work affecting equipment or other trades should be assigned before scheduling.

Will work at the flat-roof connection disturb nearby tiles or shingles?

The connection may need to be opened to reach the underlayment and flashing beneath adjoining roofing. Ask which areas will be opened, how sound materials will be reinstated, and how damaged or unavailable tiles or shingles will be handled. The extent depends on the existing detail and the proposed assembly.

Use the Pembroke Pines roofing hub for local replacement, repair, shingle, tile, metal, and broader roofing information.

Request a Flat Roofing Estimate in Pembroke Pines

Tell us about the property, the existing roof, and what you want to accomplish.

“On-time, on-budget! Absolutely fantastic company;that exceeded all expectations!”
Brad Westover · April 22, 2026 · Google Maps review