(754) 714-8445
DuPont logo

Tile adhesive review · DuPont

TILE BOND: what this roof tile adhesive means for your home

Review DuPont TILE BOND for tile roofing, with current NOAs, Polystick TU MAX compatibility and graphs comparing APOC RTA-1, AH-160 and StormBond 2.

By M&M Roofing and Construction Corp · Florida Certified Roofing Contractor CCC1332459 · Published · Updated

Get a free tile roof estimate

Compare the tile, waterproofing and attachment included in a complete roof estimate.

Add project details (optional)

No obligation. We use your details to respond to this request.

Prefer to speak now? (754) 714-8445

The short answer

TILE BOND can be a practical way to attach clay or concrete roof tiles when it is part of an approved roof system. Its one-component format avoids mixing two chemicals on the roof. For your home, the bigger questions are whether the attachment meets your roof’s wind requirements and how the waterproofing beneath the tile will be installed.

DuPont manufacturer product photograph of the TILE BOND canister, carton and dispensing hose.
Original DuPont product photograph. Packaging identifies the product family; confirm the formulation on the supplied container. This is a manufacturer reference, not an M&M Roofing project photo.

Start with the whole roof

What should a homeowner care about?

TILE BOND is a one-component polyurethane foam adhesive used with approved clay and concrete roof tiles. DuPont describes it as moisture-cured and low-expansion. It is the attachment layer in a larger system: tile, adhesive, underlayment, flashings and wood decking all have different jobs.

A simpler product format

One component means there is no A/B mixing ratio to manage during application. The crew still needs to control surface preparation, foam placement and the time between dispensing and setting the tile.

Fewer field-tile fasteners may be possible

A compatible foam-set detail can reduce fasteners through the field tiles. Edge, trim and steep-slope requirements still need to be checked, so a quote should explain the entire attachment scope.

The roof system decides the fit

Ask the roofer to match TILE BOND to the actual tile profile, underlayment and roof conditions. A product being approved does not make every combination of roofing materials an approved assembly.

Four questions behind a good tile roof

Will the tile stay attached?

The approval needs to cover your exact tile and attachment pattern. Your roof’s corners, edges and field can have different demands. Ask which approved detail the estimate includes.

Ask your roofer

Can you show me the tile approval and the attachment plan for my roof?

Choosing the tile too? Browse tile colors and profiles and our tile roofing service guide alongside the attachment options.

Make sure the estimate names the right product

The approval describes independent and interdependent attachment. In plain terms, an independent detail bonds the tile through its own underlayment contact; an interdependent detail also uses the overlap with the course below. That is why two similar foam quantities can represent different ways of carrying wind loads.

TILE BOND / TILE BOND (HFO)

NOA 26-0306.01 (opens in a new tab)

Approval date
August 20, 2026
Stated expiration
August 23, 2031

Current component approval covers the original and HFO products. It renews 22-0614.05, so older online references should not be used as the current document.

County status checked October 22, 2026: the component documents above are listed as File Approved. The tile’s own approval supplies attachment-resistance values. Read both together; a component NOA alone is not a design for your roof.

Our guide to checking a roofing product approval explains what to look for when comparing proposals.

The layer beneath your tile

Can it be used with Polystick TU MAX?

Yes—Polyglass’s compatibility table lists DuPont TILE BOND with Polystick TU MAX. Confirm the exact adhesive formulation and the complete assembly before treating that as approval for your roof.

The table names TILE BOND without a separate HFO label. The component approval’s inclusion of HFO does not, by itself, settle every formulation and underlayment combination.

Polyglass NOA 25-0121.12 · compatibility table, page 18

Compatibility answers whether materials can be used together under the listed conditions. It does not replace the fastening or adhesion requirements beneath the membrane. Read our Polystick TU MAX review for the waterproofing side of the system.

Eight tile profiles · Four adhesive choices

How does TILE BOND compare with RTA-1, AH-160 and StormBond 2?

Choose a tile below to compare all four products using that tile’s published approval. The graph covers flat and curved concrete tiles, one-piece clay and the separate Verea True Barrel cap-and-pan system. Each value links to its source page and table.

A “paddy” is a placed amount of foam; “headlap” is where the tiles overlap. The numbers measure resistance to the tile lifting and rotating, called Mf, in ft-lbf. They are not wind speeds or direct tests of the foam’s bond to Polystick TU MAX.

APOC logo

Two different APOC / ICP foams

Polyset RTA-1 · one component

APOC currently lists RTA-1 in cylinder and straw-foam formats. Its HFO component approval is NOA 25-1219.03 (opens in a new tab), with a stated expiration of January 3, 2027. The concrete-tile bars use the RTA-1 HFO rows.

Read the separate RTA-1 review

Polyset AH-160 · two components

AH-160 has its own NOA 23-0614.01 (opens in a new tab), with a stated expiration of May 10, 2027. Its bars use the named HFC/HFO1 tile entries; True Barrel retains its legacy HFC identity. HFO2 is a separate formulation.

Read the AH-160 review

For Polystick TU MAX, the Polyglass compatibility table (opens in a new tab) names RTA-1 and AH-160 HFC. It does not separately establish RTA-1 HFO or AH-160 HFO1/HFO2 compatibility. Confirm the exact supplied product and complete roof assembly.

RTA-1 details need to be reconciled before project use

Some foam amounts and contact areas in the tile approvals differ from the current RTA-1 component approval, which also has differences between its table and drawings. The graph shows the published tile values. ICP and the roof designer need to resolve the applicable details before using them for your roof.

RTA-1 component NOA · Table 1 and drawings, pages 4–7 (opens in a new tab)

Compare the same tile

How do the attachment choices compare?

Choose a tile to see its published attachment values. A higher number means more listed resistance to that tile lifting and rotating in the named arrangement. Foam amounts and patterns can differ, so these are not equal-dose tests or a universal brand ranking.

Westlake · Flat concrete

Saxony 900 Slate

Tile NOA 24-1008.12 · page 6 · Table 5 (opens in a new tab)

Lake Wales, FL production covered by this tile NOA. The RTA-1 number is a published tile-table result. Its foam amount or contact detail needs reconciliation with the current component approval before project use.

Listed attachment resistance · Mf · ft-lbf

All bars start at zero. The scale stays from zero to 140 foot-pounds when changing tiles.

Match the number to the whole detail. These are attachment-resistance moments, not wind-speed ratings or direct foam-to-underlayment bond tests. The tile, adhesive formulation, contact area and placement must match the approved roof design. Printed foam quantities identify the source entries; they are not jobsite dispensing instructions.
View all tile values and sources in a table
Published attachment values for each tile and named adhesive detail. Missing values are unavailable, not zero.
TileAdhesiveMf · ft-lbfPattern and source
Westlake Saxony 900 SlateFlat concreteAPOC Polyset RTA-1 · HFO41

Two paddies: 12 g underlayment + 10 g headlap

Source · page 6 · Table 5 (opens in a new tab)

Mass and contact minimums align with the flat HFO drawing; tile row says 1 x 10 inch headlap while component drawing says 1 x 8 inch bead and minimum 10 in2 contact. Component Table 1 versus drawing conflict still needs resolution.

Westlake Saxony 900 SlateFlat concreteAPOC Polyset AH-160 · HFC / HFO1119

Single paddy: 45 g

Source · page 7 · Table 6 (opens in a new tab)

Westlake Saxony 900 SlateFlat concreteDuPont TILE BOND65

Independent · two paddies: 25 g each

Source · page 6 · Table 5 (opens in a new tab)

The tile table names TILE BOND without a separate HFO designation. Confirm the supplied formulation.

Westlake Saxony 900 SlateFlat concreteDAP StormBond 2109

Two paddies: 8 g each

Source · page 6 · Table 5 (opens in a new tab)

Crown Windsor SlateFlat concreteAPOC Polyset RTA-1 · HFO38

Two paddies, 11 g each

Source · page 7 · Table 5 (opens in a new tab)

Tile row specifies 11 g each; component flat HFO drawing specifies 12 g underlayment and 10 g headlap. Contact is unspecified in tile table. Reconcile quantities and contact before installation.

Crown Windsor SlateFlat concreteAPOC Polyset AH-160 · HFC / HFO1119

Single paddy: 45 g

Source · page 8 · Table 6 (opens in a new tab)

Crown Windsor SlateFlat concreteDuPont TILE BOND65

Independent · two paddies: 25 g each

Source · page 7 · Table 5 (opens in a new tab)

The tile table names TILE BOND without a separate HFO designation. Confirm the supplied formulation.

Crown Windsor SlateFlat concreteDAP StormBond 2122

Two paddies: 8 g each

Source · page 7 · Table 5 (opens in a new tab)

Westlake Villa 900Medium-profile concreteAPOC Polyset RTA-1 · HFO71

Two paddies: 12 g underlayment + 10 g headlap

Source · page 6 · Table 5 (opens in a new tab)

Tile row headlap contact is 8 in2; component medium HFO drawing requires at least 10 in2. Mass matches the drawing, but contact detail needs reconciliation.

Westlake Villa 900Medium-profile concreteAPOC Polyset AH-160 · HFC / HFO187

Single paddy: 54 g

Source · page 6 · Table 6 (opens in a new tab)

Westlake Villa 900Medium-profile concreteDuPont TILE BOND67

Independent · two paddies: 25 g each

Source · page 6 · Table 5 (opens in a new tab)

The tile table names TILE BOND without a separate HFO designation. Confirm the supplied formulation.

Westlake Villa 900Medium-profile concreteDAP StormBond 255

Two paddies: 8 g each

Source · page 6 · Table 5 (opens in a new tab)

Crown TuscanyMedium-profile concreteAPOC Polyset RTA-1 · HFO44.6

Two paddies: 12 g underlayment + 10 g headlap

Source · page 6 · Table 6 (opens in a new tab)

Tile row headlap contact is 8 in2; component medium HFO drawing requires at least 10 in2. Mass matches the drawing, but contact detail needs reconciliation.

Crown TuscanyMedium-profile concreteAPOC Polyset AH-160 · HFC / HFO187

Single paddy: 54 g

Source · page 6 · Table 7 (opens in a new tab)

Crown TuscanyMedium-profile concreteDuPont TILE BOND67

Independent · two paddies: 25 g each

Source · page 6 · Table 6 (opens in a new tab)

The tile table names TILE BOND without a separate HFO designation. Confirm the supplied formulation.

Crown TuscanyMedium-profile concreteDAP StormBond 2108

Two paddies: 8 g each

Source · page 6 · Table 6 (opens in a new tab)

Westlake Barcelona 900High-profile concreteAPOC Polyset RTA-1 · HFO44

Two paddies: 12 g underlayment + 12 g headlap

Source · page 6 · Table 5 (opens in a new tab)

Tile row headlap contact is 10 in2; component high HFO drawing requires at least 18 in2. Mass matches the drawing, but contact detail needs reconciliation.

Westlake Barcelona 900High-profile concreteAPOC Polyset AH-160 · HFC / HFO167

Single paddy: 63 g

Source · page 7 · Table 6 (opens in a new tab)

Westlake Barcelona 900High-profile concreteDuPont TILE BOND58

Independent · two paddies: 12.5 g each

Source · page 6 · Table 5 (opens in a new tab)

The tile table names TILE BOND without a separate HFO designation. Confirm the supplied formulation.

Westlake Barcelona 900High-profile concreteDAP StormBond 266

Two paddies: 8 g each

Source · page 6 · Table 5 (opens in a new tab)

Crown SanibelHigh-profile concreteAPOC Polyset RTA-1 · HFO53.5

Two paddies: 22 g underlayment + 11 g headlap

Source · page 5 · Table 5 (opens in a new tab)

Tile row has 22 g underlayment and 11 g headlap; component high HFO drawing specifies 12 g each. Headlap mass is below that drawing; tile contact is unspecified. Needs reconciliation.

Crown SanibelHigh-profile concreteAPOC Polyset AH-160 · HFC / HFO167

Single paddy: 63 g

Source · page 6 · Table 6 (opens in a new tab)

Crown SanibelHigh-profile concreteDuPont TILE BOND58

Independent · two paddies: 12.5 g each

Source · page 5 · Table 5 (opens in a new tab)

The tile table names TILE BOND without a separate HFO designation. Confirm the supplied formulation.

Crown SanibelHigh-profile concreteDAP StormBond 2101

Two paddies: 8 g each

Source · page 5 · Table 5 (opens in a new tab)

Verea Spanish S · Grade 1One-piece clayAPOC Polyset RTA-1 · HFOUnavailable

No entry in the reviewed tile approval

Source · page 5 · Tables 6–7 (opens in a new tab)

No approval or performance value for this pairing is inferred from another tile.

Verea Spanish S · Grade 1One-piece clayAPOC Polyset AH-160 · HFC / HFO163

Single paddy: 34.6 g

Source · page 5 · Table 7 (opens in a new tab)

Verea Spanish S · Grade 1One-piece clayDuPont TILE BOND54

Independent · two paddies: 27.5 g each

Source · page 5 · Table 6 (opens in a new tab)

The tile table names TILE BOND without a separate HFO designation. Confirm the supplied formulation.

Verea Spanish S · Grade 1One-piece clayDAP StormBond 283

Two paddies: 9.7 g each

Source · page 5 · Table 6 (opens in a new tab)

Verea True Barrel · Grade 1Two-piece clayAPOC Polyset RTA-1 · HFOUnavailable

No entry in the reviewed tile approval

Source · page 5 · Table 6 (opens in a new tab)

No approval or performance value for this pairing is inferred from another tile.

Verea True Barrel · Grade 1Two-piece clayICP Polyset AH-160 · legacy HFC118.31

34.6 g per pan; 17.3 g on each side of cap

Source · page 5 · Table 6 (opens in a new tab)

Legacy Polyset AH-160 entry; not an HFO1 or HFO2 result. Table 6, footnote 3.

Verea True Barrel · Grade 1Two-piece clayDuPont TILE BOND89.8

12.5 g per pan; 12.5 g on each side of cap

Source · page 5 · Table 6 (opens in a new tab)

The tile table names TILE BOND without a separate HFO designation. Confirm the supplied formulation. Table 6, footnote 4.

Verea True Barrel · Grade 1Two-piece clayDAP StormBond 2Unavailable

No entry in the reviewed tile approval

Source · page 5 · Table 6 (opens in a new tab)

No approval or performance value for this pairing is inferred from another tile.

Which attachment patterns are shown?

The main graph uses RTA-1 HFO two-paddy entries, AH-160 HFC/HFO1 single-paddy entries, TILE BOND independent entries and StormBond 2 two-paddy entries where listed. Foam amounts and patterns differ; these are selected published arrangements, not equal-dose tests or each brand’s maximum result. All tile choices use the same 0–140 scale.

True Barrel uses its own cap-and-pan arrangements and the legacy AH-160 HFC entry. RTA-1 has no listed value in the two reviewed Verea clay approvals; StormBond 2 has no listed value in the reviewed True Barrel table. Those gaps are left unplotted, not assigned a strength of zero.

What does this mean for your estimate?

For Saxony 900 Slate, the selected TILE BOND detail lists 65 ft-lbf and the RTA-1 detail lists 41. For Villa 900, those entries list 67 and 71. The comparison changes with the tile and attachment pattern. Ask which exact detail meets the requirements for your roof instead of choosing a brand from one bar.

Roof height, shape, slope, edges and corners affect the required attachment. Your roofer and designer must match the chosen detail to those conditions, including the approval differences identified above.

How does TILE BOND compare with the other foams?

Start with a tile that lists the products you are comparing. The examples below use Westlake Saxony 900 Slate from the Lake Wales plant. TILE BOND has its own independent and interdependent details; they are not the same pattern or foam amount as the single-paddy StormBond 2 and APOC AH-160 example.

Published attachment values for the same tile

Choose an example. The printed weights identify entries in the tile approval; they are not jobsite dispensing instructions.

TILE BOND with Westlake Saxony 900 Slate

Listed attachment-resistance moment, Mf · ft-lbf · zero-based scale

DuPont logo

TILE BOND

Interdependent · two paddies, 12.5 g each

63 ft-lbf
DuPont logo

TILE BOND

Independent · two paddies, 25 g each

65 ft-lbf

Lake Wales plant. These two entries use different load paths and foam quantities. Interdependent attachment includes a bond at the tile overlap; independent attachment uses the tile’s own underlayment contacts. The small difference between these values is not a reason to change the specified pattern.

NOA 24-1008.12, page 6, Table 5 (opens in a new tab)

What the number means: it describes resistance to the tile being rotated upward by wind in that approved detail. It is not a wind-speed rating or a direct measurement of how strongly every foam sticks to Polystick TU MAX. Different foam quantities and patterns prevent a simple brand ranking.

The decision for your house

Ask whether the chosen attachment meets the required resistance for your actual roof, including its edge and corner zones. A higher published value for a selected detail does not compensate for the wrong product, poor contact or damaged underlayment.

For more context, read our APOC Polyset AH-160 review and Westlake tile profile comparison. The charts here use the specific current documents linked beside them.

The workmanship details you can ask about

Surface condition matters

Moisture-cured does not mean that any wet, dirty or damaged roof is ready for tile. The crew must follow the adhesive and underlayment instructions for the actual surface conditions.

Placement is part of the approval

Foam amount, contact area and position work together. Ask how those details are checked during installation. A large-looking blob in a photograph does not establish its approved attachment resistance.

Repairs need the same care

A convenient can or cylinder does not make a loose-tile repair simply a matter of adding foam. The cause of movement, tile condition, surrounding roof and underlayment need to be assessed first.

For an existing roof, our roof repair team can assess the visible issue and the work needed beneath it. A photo of a loose or broken tile cannot establish the condition of the whole roof.

Compare the full price—and who stands behind the work

Get estimates that name the same tile and full roofing scope. Check tear-off, wood-repair allowances, underlayment, flashing, tile and trim, attachment, permits and cleanup before deciding what a price difference means.

Product coverage and workmanship coverage

Ask for both the current product warranty and the contractor’s workmanship terms. The TILE BOND installation manual describes a limited manufacturing-defect warranty for one year from manufacture, with a product-price credit remedy at DuPont’s discretion. That wording is not a promise to pay for roof tear-off, labor or leak damage. The written terms supplied for your product control.

Use our Broward tile roof cost guide to plan the broader project, then get a written estimate for your home.

Frequently asked questions

Is TILE BOND a good choice for a South Florida tile roof?

It can be, when the approved tile, adhesive and underlayment details meet the requirements for your roof. Ask for the exact product and attachment detail in the estimate, along with the waterproofing and workmanship scope.

Can TILE BOND be used with Polystick TU MAX?

Polyglass NOA 25-0121.12 lists DuPont TILE BOND as compatible with Polystick TU MAX. That table does not separately name TILE BOND (HFO). Have the roofer confirm the supplied formulation and complete approved assembly rather than assume every version is interchangeable.

Is TILE BOND stronger than APOC or StormBond?

There is no useful all-roofs winner. The same tile approval lists different foam amounts and attachment patterns. Compare the exact entries and check whether the selected detail meets the wind demand for your home.

Will foam attachment stop roof leaks?

Foam holds the tiles in place. Underlayment, flashings and their connections provide the waterproofing beneath the tile. Both attachment and waterproofing need to be included in a complete roof estimate.

Does a foam-set roof have no nails or screws?

Not necessarily. Approved details can still require mechanical attachment at certain locations or slopes. Ask which parts of the roof use foam and where fasteners or other attachment are required.

Is TILE BOND cheaper for my roof?

A canister price does not establish the installed roof price. Roof geometry, selected tile, approved foam pattern, preparation, access and labor affect the proposal. Compare itemized estimates for the same complete scope.

Which APOC / ICP products are included in the comparison?

Both Polyset RTA-1 and Polyset AH-160 are shown separately. RTA-1 uses one component; AH-160 uses two. They have different NOAs, foam amounts and attachment details. The graphs name the formulation and tile for each result. RTA-1 has no listed result in the two Verea clay approvals reviewed here, and differences between its component and tile instructions need to be resolved before project use.

What do the strength numbers in these graphs mean?

They are published attachment-resistance moments, measured in ft-lbf, for a specific tile and foam detail. A larger value means more listed resistance to that tile lifting and rotating in that arrangement. It is not a wind-speed rating or a direct test of the bond to Polystick TU MAX. Your roofer still needs to compare the chosen detail with your roof’s required wind resistance.

Sources checked October 22–23, 2026

Product approvals are revised and renewed. Confirm the current document for the exact product, plant and roof system when your permit is prepared. This guide is general information for homeowners, not an engineering or permit determination for a specific roof.

Let’s compare the complete roof for your home

Talk through tile choices, waterproofing, approved attachment and the work included in your estimate.

Call (754) 714-8445